Blackview S8 4G Phablet 10/19/2017Blackview S8 4G Phablet 5.7 inch Android 7.0 MTK6750V 1.5GHz Octa Core 4GB RAM 64GB ROM 8.0MP + 0.3MP Dual Front Cameras Touch Sensor
● Display: 5.7 inch, 1440 x 720 Pixel screen
● CPU: MTK6750V 1.5GHz Octa Core
● System: Android 7.0
● RAM + ROM: 4GB RAM + 64GB ROM
● Camera: 8.0MP ( SW 13.0MP ) + 0.3MP front cameras + 13.0MP + 0.3MP back cameras
● Sensor: Ambient Light Sensor, Gravity Sensor, Proximity Sensor
● SIM Card: dual SIM dual standby. 1 Micro SIM card + 1 Nano SIM card
● Feature: GPS
● Bluetooth: 4.0
2G: GSM 850/900/1800/1900MHz
3G: WCDMA 900/2100MHz
4G: FDD-LTE 800/900/1800/2100/2600MHz Check it here.
I changed the 'disable unused GPIO pins' option to 'on' in BIOS
and I do not remember it, but I think I changed 'stats after g3' to s0 and I saved it
after, it did not turn on. Backlight and screen did not come in
my tablet always booted when I connected power trough otg hub. but it didn't turn on like before
So I tried to disassemble and unplug the BIOS battery, but it did not have a bios battery and there was a chip called '25Q64FWIM'(I searched it it was EEPROM)
I thought I should reset it
I connected 8pin to each other and tried to boot but it didn't boot. However, when I disassemble it, I noticed that when the battery is repluged, the CPU is in a cold state. When I press the power button, the CPU became hot(seems like turned on but no screen). Can you tell what the symptoms are and how to fix them?
before doing that I'd cleared all partition of internal rom and installed win 10 on there ((haha, installing driver was very difficult, if you want some help, tell me)
Hello, I’ve got some strange issue that I’m eager to solve here.
I’ve got Windows 10 Tablet from China. It’s called Onda 919 Air CH. It’s based Intel Cherry Trail platform so it has Intel Atom x5-Z8300 CPU and Intel HD Graphics (GEN 8).
When I turn it on and run any 3d application (games, 3dmark) it will work just fine. Even Fur Mark (stress test for GPU) works perfectly for hours. But if you send it to sleep and wake up, in 3d applications you will see some artifacts and then driver reboots.
I've got video with this problem http://www.youtube.com/watch?v=TZpa_DyZgUs
At first i run Fur Mark from clean boot and it worked for 10 minutes. Then I sent tablet to sleep and after that Fur Mark worked only for 3 min and driver crashed. Same thing in 3dmark06, in hl2 etc.
So after sleep/wake up smth breaks in driver and such thing happens.
What could it be?
I tried another GFX driver, tried to re-install windows, nothing helps.
Asked two other owners of this wonderful tablet, but they don't have driver crash in this benchmark after sleep mode.
V698 4G models V1.0.7 firmware Brush Pack
File size: 463MB
1 optimization algorithm to improve the speed and accuracy of GPS positioning.
1, this Brush Pack for machine brush package, should be used with Brush tool, connected to a computer operating Brush, apply only to boot the machine or system failure occurs use.
2, machine brush package upgrade will clear all the data plate, please make a backup of work in front of Brush.
All available download files are located in the Downloads directory.
“ Downloads “ button at the top of this page
Available files are grouped by Device named category
All files are listed in reverse chronological order ( newest upload file is listed first )
Most device categories each have multiple pages of listed file names.